---
title: "How many packs of flooring do I need? | BuildBatch"
description: "Floor area, plus an allowance for cuts, divided by the coverage on the pack and rounded up. A worked example, a quick table, and two pack sizes."
url: https://buildbatch.co.uk/guides/how-many-packs-of-flooring-do-i-need/
---

[Guides](https://buildbatch.co.uk/guides/)

# How many packs of flooring do I need?

4 min read · Updated 8 November 2026

Work out the floor area in square metres, add an allowance for cuts, divide by the area one pack covers and round up to the next whole pack. A 4.2 m × 3.6 m room is 15.12 m², 16.632 m² with 10% extra, and needs 10 packs that each cover 1.84 m².

Built with AI tools; not yet checked by a tradesperson.

Read here; this page sends and keeps nothing.

[Work out the flooring for this room, then change it to yours](https://buildbatch.co.uk/start/#v=1&job=flooring&walls=none&ceiling=none&trim=none&units=m&length=4.2&width=3.6&surface=sound&subfloor=unsure&ground=unsure&fitting=unsure&floor=quick&floor.covering=laminate&floor.underlay=unsure&end=15)

![Oak-effect laminate laid over half a floor, grey underlay on the rest, and a stack of wrapped plank packs.](https://buildbatch.co.uk/img/guides/how-many-packs-of-flooring-do-i-need.webp)

## The four steps

1. **Floor area** = length × width, in metres. For an L-shaped or awkward room, split the floor into rectangles and add them.
2. **Area to buy for** = floor area × 1.1, for 10% extra.
3. **Packs** = area to buy for ÷ the coverage of one pack.
4. **Round up** to a whole pack, always, even when the answer is only just over a whole number.

Work with the unrounded figures and round once, at the end.

## Where the pack coverage comes from

It is printed on the pack, in m² per pack. It changes from one product to the next, and even between board sizes in the same range, so take it from the pack you are buying. For laminate the calculator counts in 1.835 m², Quick-Step’s own pack size and the smaller of two makers’ sizes, until you give yours, and offers both makers’ sizes, one tap each, beside the number; for engineered wood and vinyl planks it asks for the figure (“Pack size?”). The figure off your pack comes first.

The 10% is a starting figure, not a standard. A diagonal or herringbone lay, a patterned board or an awkward room needs more; the [wastage allowance guide](https://buildbatch.co.uk/guides/wastage-allowance-explained/) says when.

## Worked example

A room 4.2 m × 3.6 m, packs covering 1.84 m², 10% extra.

- Floor area: 4.2 × 3.6 = 15.12 m²
- Plus 10%: 15.12 × 1.1 = 16.632 m²
- Packs: 16.632 ÷ 1.84 = 9.04
- Rounded up: **10 packs**, covering 10 × 1.84 = 18.4 m²
- Left over: 18.4 − 16.632 = about 1.77 m²

Nine packs would cover 16.56 m², about 0.07 m² short of the 16.632 m² to buy for. It is a small gap, but it is a gap, so the answer is 10.

## A quick table

At 10% extra:

| Floor | To buy for | Packs of 1.84 m² | Packs of 2 m² |
| --- | --- | --- | --- |
| 3 m × 3 m = 9 m² | 9.9 m² | 6 | 5 |
| 4 m × 3 m = 12 m² | 13.2 m² | 8 | 7 |
| 4.2 m × 3.6 m = 15.12 m² | 16.632 m² | 10 | 9 |
| 5 m × 4 m = 20 m² | 22 m² | 12 | 11 |
| 6 m × 4.5 m = 27 m² | 29.7 m² | 17 | 15 |

Two things stand out. The pack size changes the count, by one pack in most rows and by two in the largest. And the 5 m × 4 m room in 2 m² packs comes to exactly 11: a whole-number answer does not buy an extra pack, because the 10% is already in it.

## Two pack sizes: the combination matters

When a floor is sold in more than one pack size, the question is not only how many, but how many of each.

Say a floor came in packs of 1.84 m² and half packs of 0.92 m², and you need 16.632 m²:

| Combination | Covers | Left over |
| --- | --- | --- |
| 10 × 1.84 m² | 18.4 m² | about 1.77 m² |
| 9 × 1.84 m² + 1 × 0.92 m² | 17.48 m² | about 0.85 m² |
| 9 × 1.84 m² | 16.56 m² | about 0.07 m² short |

The second line covers the floor with 0.92 m² less left over. Whether it also costs less depends on the prices of the two sizes, which only the shop can tell you.

The planner on this site counts one pack size at a time, the one you give it, so a mix of two sizes is a sum to do as above. Where two combinations cover the floor, the one with less left over wastes less; the shop’s prices decide which costs less.

## Before you buy

- Buy all the packs at once, and where the packs show a batch or lot number, check that they match: the colour can vary from one batch to the next.
- Keep a board or two back after laying, for a repair later.
- The underlay, any membrane, the beading and the door bars are separate lines. See [underlay and damp-proof membranes](https://buildbatch.co.uk/guides/underlay-and-damp-proof-membranes/) and [measuring for skirting, beading and scotia](https://buildbatch.co.uk/guides/how-to-measure-skirting-and-beading/).

## Do it with BuildBatch

Open the [flooring calculator](https://buildbatch.co.uk/flooring-calculator/), type the room, and answer “What does one pack cover?” with the m² printed on your pack. It gives the packs, and the pack’s line in the shopping list shows the working and what is left over.

Having it laid instead: [the cost to lay laminate flooring](https://buildbatch.co.uk/costs/laying-laminate-flooring/) gives what UK cost guides publish, each with the day read, and the sum for a 4 × 3 m room.

## What this guide does not cover

Carpet and sheet vinyl, which are sold by roll width and need a different sum. Tiles laid to a set pattern. Stairs. Whether the floor suits the room, the subfloor or underfloor heating: the flooring’s instructions decide, so check first.

## Related guides

- [Measuring for laminate flooring](https://buildbatch.co.uk/guides/measuring-for-laminate-flooring/)
- [Wastage allowance explained: why 10%, and when to allow more](https://buildbatch.co.uk/guides/wastage-allowance-explained/)
- [Damp-proof underlay or a membrane on a concrete floor?](https://buildbatch.co.uk/guides/underlay-and-damp-proof-membranes/)
- [How much underlay do I need?](https://buildbatch.co.uk/guides/how-much-underlay-do-i-need/)

## Questions

**How many packs of flooring for a 4.2 m by 3.6 m room?**

With packs covering 1.84 m² and 10% extra for cuts, 10 packs. The floor is 15.12 m², 16.632 m² with the extra, and 16.632 ÷ 1.84 = 9.04, which rounds up to 10.

**Can I round down if it is only just over?**

No. In that room nine packs would leave you about 0.07 m² short. A real shortfall, however small, always buys the next pack.

What changed: Says that the calculator counts laminate in Quick-Step's 1.835 m² pack, the smaller of two makers' sizes, until you give yours, where it asked for the size.

A whole list worked out: [How many packs of laminate for a 3 x 4 m bedroom?](https://buildbatch.co.uk/examples/laminate-flooring-in-a-3-by-4-m-bedroom/)

[All calculators](https://buildbatch.co.uk/calculators/) · [Example lists and tables by room size](https://buildbatch.co.uk/examples/) · [What it costs to have it done](https://buildbatch.co.uk/labour-costs/) · [Where the figures come from](https://buildbatch.co.uk/sources/)
