How much carpet for a 4.2 x 3.6 m bedroom?
A 4.2 × 3.6 m bedroom has 15.12 m² of floor and needs one unjoined piece of carpet 4 m wide × 4.3 m long (17.2 m²), which is 4.3 linear metres from a 4 m roll, and 2 rolls or packs of underlay of 15.07 m² each (30.14 m²). The roll width, the trimming allowance and the underlay pack are example figures, not a product’s: check the roll width, the pile direction and any joins with the shop or fitter.
This worked example fits one rectangular bedroom from one unjoined piece of carpet. No roll width is given, so the planner tries both orientations against the widths carpet is usually sold in, 4 m and 5 m, and takes the one that needs least roll in one piece.
How this example was made
It was worked out when this page was built, by the same room planner and formulas as the editable list. The room figures are round examples. The product figures are the planner’s own, not figures for a product: a typical figure where it has found one, such as a paint’s coverage, and a labelled example otherwise. The sentence under the heading says which.
Automated tests compare its list with the planner. No price is shown or used.
The room and assumptions
Room: 4.2 m × 3.6 m; 1 door. Work: carpeting.
- One rectangular room, 4.2 m × 3.6 m, measured in metres.
- 1 door entered for the threshold-bar count. Openings are not taken off the floor.
- Carpet: one rectangular room, one unjoined piece from a 4 m roll. The 0.1 m trimming allowance is added to each room measurement. Check the pile or pattern direction before ordering. No roll width was given: the 4 m width is the standard one that needs least roll for this room. Enter the width the shop sells in the planner.
- The carpet cut is rounded once up to the shop step; underlay is rounded once up to whole packs. Working uses unrounded figures.
- Gripper rods or the fixing system for this carpet: counted from the size each is typically sold in or how far it typically goes, from makers' and merchants' own pages read on 12 October 2026. The label on what you buy says its own figure.
- The figures for carpet and carpet underlay are examples, not the figures of any product. Enter the roll, shop and underlay figures for a closer answer.
The shopping list
6 lines marked Need. Lines that this job does not need are left out here; the full planner shows them too.
Need
Carpet
Need1 × 4 m wide × 4.3 m long (17.2 m²)
Why, and what to check
One unjoined piece, along the room length: 4 m wide × 4.3 m long. The measured floor is 15.12 m²; the full roll-width piece is 17.2 m². No roll width was given, so of the widths carpet is usually sold in (4 m and 5 m), this is the one that needs least roll for this room in one piece; the shop you buy from may not sell it.
Check: This is the smaller one-piece cut that fits. Check the pile or pattern must run this way before ordering.
Carpet underlay
Need2 × 15.07 m² roll or pack (30.14 m²)
Why?
15.12 m² of floor; one chosen roll or pack covers 15.07 m².
Gripper rods or the fixing system for this carpet
Need10 × 1.5 m rod
Why, and what to check
Round the room, less the doorways: 14.8 m of wall, in rods of 1.5 m.
Check: A carpet that is stuck down, or laid on a floor that cannot take pins, is fixed another way: the carpet's instructions say. No gripper goes across a doorway: a door bar does.
Door threshold bars
Need1 × door bar
Why, and what to check
One for each doorway: 1 door in this example.
Check: Choose each bar for the neighbouring floor finishes and finished heights.
Tape measure, trimming knife and carpet fitting tools
NeedWhy, and what to check
For checking the room and cutting and fitting the chosen carpet system.
Check: Carpet stretching, seaming and fixing need suitable tools and experience. Follow the carpet and underlay instructions or use a fitter.
Knee protection, gloves and eye protection
NeedWhy?
Carpet fitting involves sharp blades, gripper pins and prolonged kneeling.
Before you use it
- Measure the longest and widest points, including recesses that need carpet.
- Check the available roll width and whether the pile or pattern must run one way.
- Have a fitter confirm the cut, joins, gripper, underlay and threshold before ordering.