How much tile adhesive and grout do I need?

5 min read · Updated 9 November 2026

A 20 kg bag of tile adhesive covers about 6.7 m² of wall with a 6 mm notched trowel. For 17.73 m² of wall in 300 × 600 mm tiles that is 3 bags of adhesive and 1 bag of grout. A 15.1 m² floor in 600 × 600 mm tiles takes 6 bags and 1. If your bag says the m² it covers, divide the area by that instead.

Built with AI tools; not yet checked by a tradesperson.

Read here; this page sends and keeps nothing.

Work out the tiles for this room, then change it to yours

A floor tile’s adhesive bed and joint, in sectionThe floor, flat and soundAs spread: ridges from a 10 mm notchabout 10 mm highPressed in: a bed of about 5 to 6 mmTile, 10 mmAdhesive3 mm joint: a spacer, then grout over it
A 10 mm notch leaves ridges about 10 mm high; pressed in, they make a bed of about 5 to 6 mm, which is why a floor takes about 7 kg a square metre. The 3 mm joint and the 10 mm tile are examples.

The sum

  • Adhesive = the area to tile × the kilograms a square metre ÷ 20 kg, rounded up.
  • Grout = the area × the kilograms a square metre ÷ 5 kg, rounded up.

The trowel’s notch sets the adhesive. On a wall, by BuildBatch’s own rule (under review), a tile up to 600 mm on its long side takes a 6 mm notch and a larger one 12 mm. The 600 mm limit is the site’s, not a maker’s: the makers’ sheets read give a wall tile over 300 × 300 mm a deeper notch on a solid bed. That is 10 mm on BAL’s Rapid-Flex One sheet and 8 to 10 mm on Mapei’s Mapeker Rapid-Set Flex sheet. A typical 6 mm bed takes about 3 kg a square metre, the middle of four UK makers’ sheets rounded up. A 12 mm bed takes about 10.5 kg, the middle of Sika’s Supracoat sheet, the only one found with a 12 mm row. On a floor a tile up to 300 mm on its long side takes 6 mm at 5.25 kg, the middle of Sika’s Supracoat sheet’s row for 30 cm tiles. The 3 kg is a wall figure: the UK makers’ sheets give a floor no 6 mm row, and BAL’s says at least a 3 mm bed on a floor. The small floor tile’s row is under review. One up to 600 mm takes a 10 mm notch, a typical 7 kg (five makers’ floor adhesives), and a larger one 12 mm (sources).

The joint sets the grout. Grout fills the joints, so large tiles with thin joints take little. Norcros Adhesives’ rule gives it: (width + length) × joint × tile thickness × 1.7 ÷ (width × length), all in mm, is the kilograms a square metre.

Count both on the area you tile, without the 10% for cuts.

Worked example

A room 4.2 m × 3.6 m and 2.4 m high, with one door and one window: the room in how many tiles do I need? The walls have a 2 mm joint and 8 mm tiles; the floor a 3 mm joint and 10 mm tiles.

Tiled Tile Adhesive Bags of 20 kg Grout Bags of 5 kg
Wall to 1.2 m, 17.73 m² 300 × 600 mm 17.73 × 3 = 53.2 kg 3 0.136 kg/m², 2.41 kg 1
Wall to the ceiling, 35.17 m² 300 × 600 mm 35.17 × 3 = 105.5 kg 6 0.136 kg/m², 4.78 kg 1
Floor, 15.12 m² 600 × 600 mm 15.12 × 7 = 105.8 kg 6 0.17 kg/m², 2.57 kg 1

At 3 kg a square metre a 20 kg bag covers about 6.7 m² of wall, and at 7 kg about 2.9 m² of floor. Keep the spare grout for repairs.

What changes it

  • Your bag’s own figure. Divide the area by the m² it says it covers. Say a bag of adhesive covers 4 m² and one of grout 6 m². The same room’s floor is 15.12 m². Adhesive: 15.12 ÷ 4 = 3.78, so 4 bags. Grout: 15.12 ÷ 6 = 2.52, so 3 bags.
  • Your maker’s own figure. Mapei’s Mapeker Rapid-Set Flex gives 2.5 to 3 kg a square metre with a 6 mm trowel for normal-size tiles. The wall to 1.2 m in 300 × 300 mm tiles takes 3 bags at either figure. Mapei counts a 300 × 600 mm tile as large: 8 to 10 mm and 4 to 5 kg a square metre, so 17.73 m² takes 4 to 5 bags, more than the planner’s 3. BAL’s Rapid-Flex One gives 2 kg on a dry wall, 2 bags for the same wall; Sika UK’s SikaCeram-240 about 5.7 kg, 6 bags.
  • Smaller tiles or wider joints. They take more grout: 250 × 400 mm wall tiles at the same joint take 0.18 kg/m².
  • A wall tile over 600 mm. By BuildBatch’s rule it takes a 12 mm notch and 10.5 kg a square metre, three and a half times the 6 mm row. That figure is from the one sheet found with a 12 mm row, Sika’s Supracoat sheet, published in Malaysia. BAL’s and Mapei’s sheets give a large wall tile about 3.85 to 5 kg on a 10 mm solid bed, so your bag may go much further.
  • Buttering the backs. Large tiles, an uneven floor or a solid bed under a floor tile take more adhesive than the ridges alone.
  • A timber floor. Use a flexible adhesive: the floor moves.

The tiles themselves are in how many tiles do I need?, and the rest of the list for a wall in what you need to tile a wall.

How to do it

  1. Make the floor ready: screw backer board or overlay ply over timber. A concrete floor or screed must be dry and flat first.
  2. Lay the tiles out dry from the middle of the room, so the cut tiles at the walls are not slivers.
  3. Spread adhesive over about a square metre at a time with the notched trowel, and bed each tile in so it is fully supported.
  4. Keep the joints even with spacers, and check the tiles are level with each other as you go.
  5. Cut the edge tiles last, leaving a small gap at the walls.
  6. Keep off the floor until the adhesive has set, then grout it and wipe the face clean with a damp sponge. Grout after 24 hours on floors, for a standard-set adhesive (ARDEX).
  7. Seal the gap round the edge of the floor, and where it meets a bath or a shower tray, with silicone.

How long it takes

A tiler lays 8 to 12 m² of floor tiles a day, and 8 to 14 m² of large porcelain tiles (MyJobQuote and Trade2Base). Difficulty: moderate.

Tools and materials

  • A floor ready to tile: a backer board or an overlay on timber, or a flat, dry screed.
  • A notched trowel, a tile cutter or a wet saw, a spirit level, a grout float, a sponge, a bucket and a mixing paddle.
  • Tile adhesive for the floor tiles.
  • Tile spacers: small crosses that keep the joints even.
  • Grout that fills the joints between the floor tiles.
  • A bucket and a sponge.
  • Silicone sealant for the joints where tiles meet a bath, a basin or a worktop, where grout would crack.

Common mistakes

  • Tiling straight onto floorboards. They flex and the tiles crack: board them over first.
  • Starting at one wall. The far wall gets a thin cut: start from the middle.
  • Leaving gaps under the tiles. A tile with hollows behind it cracks: bed it in fully.
  • Walking on the floor too soon. Keep off it for the time on the adhesive's bag.
  • Grouting the edge against the wall. The floor needs room to move: silicone it.

When to get someone in

Get a tiler in for large-format or stone tiles, underfloor heating, or a floor that needs levelling.

Having it done, floor tiling: labour only, £15 to £60 per m². These are published UK figures, each its publisher's own, and not a quote: every figure, its source and the sum for a room: floor tiling.

Sources

  • The 3 kg for a 6 mm notch on a wall: the middle of four UK makers’ own sheets, rounded up so the buyer is not left short: BAL Rapid-Flex One data sheet, May 2025 (“Wet Wall 6mm Notched (solid bed) 0.4m²/kg”, 2.5 kg; “Dry Wall 6mm Notched 0.5m²/kg”, 2 kg); Mapei’s Mapeker Rapid-Set Flex sheet (“normal size tiles (6 mm notched trowel): 2.5-3 kg/m²”); Saint-Gobain Weber’s weberset SPF listing on NBS Source (“3.0 kg/m² (using a notched trowel with 6 x 6 mm, notches at 12 mm centres”; Weber’s own site could not be read); and Sika UK’s SikaCeram-240 Flexible Rapid sheet, November 2021 (“approx. 3.5 m2 using 6 mm notched trowel” from a 20 kg bag, about 5.7 kg). Their middle is 2.875 kg. Read 8 and 9 November 2026. Until 9 November 2026 the wall’s figure was 5.25 kg, the middle of the Supracoat sheet’s 6 mm row below, which a floor tile up to 300 mm still takes.
  • The 10.5 kg for a 12 mm notch: the middle of the figures on Sika’s data sheet for Supracoat Tile Adhesive, December 2024, published by Sika in Malaysia: 10 to 11 kg with a 12 mm one, which the sheet gives for large tiles up to 3600 cm² on inside floors, the only sheet found with a 12 mm row; its 6 mm row, about 5 to 5.5 kg for 30 cm tiles, is no longer the wall’s but is still a floor’s for a tile up to 300 mm, at its middle, 5.25 kg. Read 10 October and 8 November 2026.
  • The 7 kg for a 10 mm notch: five makers’ floor adhesives (BAL, Mapei, ARDEX, Instarmac and Bostik), which give 1.05 to 1.5 kg a square metre for each mm of bed, read 12 October 2026.
  • What the makers give a wall: BAL Rapid-Flex One data sheet, May 2025, page 5, a 6 mm notch on an inside wall for tiles up to 300 × 300 mm and a 10 mm notched solid bed otherwise (its coverage for that trowel, 0.26 m² a kilogram, is given for exteriors and floors); and Mapei’s sheet below, an 8 to 10 mm notch at 4 to 5 kg a square metre for large sizes, which it counts as over 300 × 300 mm. Both read 19 October 2026.
  • The grout rule: Norcros Adhesives’ wall tile grout data sheet (2014). The 1.7 lies between ARDEX’s 1.75 and Bostik’s 1.6, read 10 October 2026.
  • Mapei: Mapeker Rapid-Set Flex technical data sheet, reference 68-4-2026 (UK), read 5 October and 9 November 2026.
  • The 2 and 3 mm joints, the 8 and 10 mm tiles and the 4 and 6 m² bags are BuildBatch’s examples, not a product’s. The typical figures, with their addresses, are on the sources page.

The steps' times and waits:

  • MyJobQuote: a tiler laying 8 to 12 m² of floor a day, read 3 October 2026.
  • Trade2Base: large-format porcelain floor tiles (600 × 600 mm and over): 8 to 14 m² a day, for a sole tiler, read 18 October 2026.
  • ARDEX: ARDEX X 7: grout after 8 hours on walls, 24 hours on floors, read 18 October 2026.

Questions

How many bags of tile adhesive do I need?

The area × the kilograms a square metre takes ÷ 20 kg, rounded up. With a 6 mm notched trowel, at a typical 3 kg a square metre, 17.73 m² of wall is 53.2 kg: 3 bags of 20 kg. If your bag says the m² it covers, divide the area by that.

How much tile adhesive per square metre?

Typically about 3 kg with a 6 mm notched trowel on a wall: the middle of four UK makers' sheets (BAL, Mapei, Weber and Sika UK), rounded up. On a floor a tile up to 300 mm is still counted at 5.25 kg with the 6 mm trowel, Sika's Supracoat figure: the UK sheets give a floor no 6 mm row. With a 12 mm one, 10.5 kg, the middle of Sika's Supracoat sheet, the only one found with a 12 mm row. With a 10 mm one, about 7 kg, from five makers' floor adhesives. The makers' own 6 mm figures run from 2 kg (BAL, on a dry wall) to about 5.7 (Sika UK): the bag you buy says its own.

How many bags of grout do I need?

Usually one 5 kg bag for a room of large tiles. 300 × 600 mm wall tiles with a 2 mm joint take 0.14 kg a square metre: 2.4 kg for 17.73 m². Small tiles and wide joints take more.

Do I add 10% for cuts to the adhesive and grout?

No. Count them on the area you tile. The 10% for cuts goes on the tiles only: see how many tiles do I need?

What changed: The 6 mm notch's figure is 3 kg a square metre, the middle of four UK makers' sheets, where it was 5.25 from one Malaysian sheet: 3 bags for the wall, not 5.